Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
How do you really feel about A Step-by-Step Guide to Installing a Bathtub?
![Tools You Need to Install a New Bathtub](https://www.makingmanzanita.com/wp-content/uploads/2022/08/leveling-floor-in-bathroom-with-floor-patch-before-install-bathtub-1024x576.jpg)
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a new one is also a moderately hard project. If the old bathtub is easily available, the task can move quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have certified on your own for the task and fit trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you set up a new bathtub in your washroom if you have actually already purchased a brand-new tub and also do not require to change the arrangement of your previous water pipes.
Your tools and also product list need to consist of the following:
Preparing for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly come from the pipes. Once the supply pipes have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub till the spirit level reviews level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow outlet and the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will resolve it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing difficulties with wetness and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and installations. They are marketed in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![How to Install a Bathtub Yourself](https://www.myjobquote.co.uk/assets/img/cost-of-installing-a-new-bath-1.jpg)
As a reader about How to Install a Bathtub Yourself, I was thinking sharing that portion was a good idea. Do you know another person who is curious about the subject? Take a moment to promote it. I treasure reading our article about Tools You Need to Install a New Bathtub .
Don't delay; get expert help. Report this page